Underground stormwater system meets enviro, footprint requirements at National Guard Readiness Center

BROOKFIELD, CT, April 30, 2010 -- The Massachusetts Army National Guard (MAARNG), stationed in Methuen, Mass., needed to redesign its existing Methuen Readiness Center to meet the MAARNG mission, readiness and training requirements...

Apr 30th, 2010
Pennwell web 300 203
At the Methuen Readiness Center in Methuen, Mass., CULTEC's Recharger 180HD underground stormwater system captures, retains and detains a large amount of runoff in a relatively small footprint.

BROOKFIELD, CT, April 30, 2010 -- The Massachusetts Army National Guard (MAARNG), stationed in Methuen, Mass., needed to redesign its existing Methuen Readiness Center to meet the MAARNG mission, readiness and training requirements. The facility was inadequate in size and did not meet the current Anti-Terrorism and Force Protection (AT/FP) requirements.

Redesigned by OMR Architects, the new Readiness Center consisted of a 42,000 square-foot, two-story facility that included an assembly hall, administrative, training and support spaces, and kitchen and maintenance bays. In addition to the new building, the 5.5-acre site featured about 3.4 acres of military and civilian parking area.

When it came to designing a stormwater management system for the project, Boston, Mass.-based Nitsch Engineering Inc., was faced with a number of onsite challenges, including land constraints, 148-foot AT/FP site boundary setback and related stand-off distances and proximity to nearby wetlands. Additionally, the project occurred within the 100-year flood plain of the Merrimack River.

As the redesigned site featured an increased number of impervious surfaces, the MAARNG stormwater plan needed to limit the post-development rate of runoff from the site to no greater than pre-development levels. To achieve that, as well as solve the challenge of space constraints, the engineers selected CULTEC Recharger® 180HD underground chamber system, a Best Management Practice. Specific to the MAARNG site, the system was designed to detain runoff onsite during small storm events and retain it during larger storm events.

"Granted the limited space we had to work with and absence of a municipal connection, an underground solution was the only way to go," said Anthony Donato, P.E., LEED A.P. at Nitsch Engineering Inc. "We know CULTEC as a reliable and economic solution. The arch chamber design ensures the system's structural integrity, and the heavy duty models work well in high traffic applications, as in this case, where the system is located under the parking lot."

The engineers used HydroCAD® modeling software to design the stormwater system; CULTEC also offers a free HydroCAD CULTEC edition that allows constructing basic watershed models of up to five nodes, including storage, runoff, and routing calculations for the company's chambers.

CULTEC offers a variety of chamber sizes to accommodate almost any site constraint, and its higher profile Recharger series make optimal use of large storage capacities in a smaller footprint. The Recharger 180HD is 20.5 inches high, 36 inches wide and has a chamber storage capacity of 3.45 cubic feet per linear foot.

To address the facility's stormwater runoff storage needs, CULTEC retention and detention system provided 11,052 cubic feet of storage. The project required 300 Recharger 180HD units, which were installed in a 6,530 square-foot bed and backfilled with 573 tons of stone.

The CULTEC system installation began with excavating a bed, laying CULTEC non-woven polypropylene filter fabric along the sides and the bottom of the bed and then adding a six-inch layer of crushed stone. The chambers were arranged in the bed, fed using CULTEC unique internal manifold feature, and covered with six inches of crushed stone and a layer of filter fabric. The entire system was installed in about two days.

For more information about CULTEC and its products, visit www.cultec.com .

About CULTEC
In 1986, CULTEC introduced its Contactor® and Recharger® HDPE septic and stormwater chambers and helped begin a revolution toward the use of plastic construction products. Since then, several product developments and strategic alliances have made CULTEC a cutting-edge R&D-based manufacturer. CULTEC chambers can be used as subsurface retention or detention systems and as replacements for ponds, concrete structures or pipe and stone installations.

CULTEC manufactures nine different chamber sizes ranging from 8.5" -- 32" to accommodate almost any site parameter. The chambers' perforated sidewalls and fully open bottoms promote maximum infiltration capability and allow for the transfer of high volumes of water at a low velocity. The units can be installed singularly or in series in single- or multi-layer beds.

In addition, CULTEC developed its own in-line side portal manifold system, which eliminates the need for a conventional pipe header system, and water quality unit for maintaining CULTEC chamber systems. CULTEC products meet H-25 wheel load requirements, have a 10-year warranty and are currently modeled in HydroCAD®, Bentley Systems Inc.'s PondPack®, BOSS International's StormNET®, and Streamline Technologies' ICPR®.

CULTEC's technical staff offers free design assistance including preliminary calculations and job-specific CAD details. A free CULTEC StormGenie™ -- AutoCAD® Plug-In for designing CULTEC systems and a free HydroCAD CULTEC custom edition are also available from the company. In addition, CULTEC products can contribute to the U.S. Green Building Council's credits, under the LEED rating system, when the project is designed per LEED requirements.

###

More in Stormwater Management